>

GP1800   GP1800R

  
  

ISLAND RACING
GP1800
FULL MOD OEM RIDEPLATE

Additional speeds up to 3+ MPH over an unmachined OEM rideplate.
Make no mistake! ISLAND RACING RIDEPLATES are the WORLDS FASTEST Rideplates available anywhere.
WE ARE THE ORIGINATORS OF THE MODIFIED RIDEPLATES
ACCEPT NO IMITATIONS
  
ISLAND RACING
FULL MOD RIDEPLATE
$550.00 ( New OEM Rideplate ) 
$350.00 ( Mod Your Rideplate )
  
***NOTE***
ISLAND RACING'S MODIFIED RIDEPLATES ARE THE WORLDS FASTEST RIDEPLATES AVAILABLE!
RIDER TESTED AND PROVEN!

  

PARTS & ACCESSORIES

  

3M MARINE ADHESIVE SEALANT 4200 FAST CURE
06560 $29.99 White 10 Ounce
06564 $29.99 Black 10 Ounce

We all know "pump sealing" is a must on all Yamaha models for reducing cavitation and increasing performance. 3M 4200 FAST CURE is the most commonly used sealant by ALL watercraft owners and IS the recommended sealant to use for your Yamaha pump sealing needs.

ADA BILLET DRIVE COUPLER SET
34-7020 $229.95

AIRHEAD BUNGEE DOCK LINE
AHDL-4 $11.99 4' Stretches to 5.5'
AHDL-5 $12.99 5' Stretches to 7'
AHDL-6 $13.99 6' Stretches to 9'
  
AIRHEAD Bungee Dock Lines absorb shock to boats, cleats, docks, pylons and other hardware. The bungee cord is hidden inside the rope and acts as a built-in snubber. Two foam floats protect the boat from chafing. There's a sliding adjustment at both ends for quick docking. Recommended for docking boats and PWC's up to 3,500 pounds. Tensile strength is 2,150 pounds. Black/Blue/Red color scheme.

AIRHEAD HULL HUGR PWC FENDER
HH-P1B $21.99
  
Docking a PWC has never been safer with the introduction of the HULL HUGR PWC Fender. Engineered specifically for PWCs, it hinges in the center to better protect PWC bodies from docks designed for bigger boats. It hooks under the rub rail with a molded acetyl hook integrated into the back of the fender. If your PWC has them, you'll want to connect the top of the fender to a cleat or ski eye with the adjustable strap and vinyl dipped steel hook provided. If not, simply thread the strap though the rubber block provided and place it inside the PWC's storage compartment, then shut it. The block anchors the fender strap perfectly and will not damage the body. We recommend 2 fenders per PWC. Fits all PWCs.

AMSOIL SYNTHETIC MARINE ENGINE OIL 10W-40
WCFQT $12.65
 
For use in 4-stroke gasoline fueled engines in marine applications. Offers unsurpassed wear protection, viscosity stability, low volatility and excellent rust protection. NMMA FC-W approved and "warranty certified". For use in 4-stroke outboard and marine inboard engines. Also excellent for personal watercraft.

AMSOIL OIL FILTER
EAOM134 $15.15

AMSOIL Ea® Oil Filters feature advanced full-synthetic media that traps and holds a greater amount of small, wear-causing contaminants compared to conventional filters. Efficiency is the filter's ability to capture contaminants. The more efficient a filter is, the more contaminants it will remove from the oil. AMSOIL Ea Oil Filters have one of the best efficiency ratings on the market. Ea Oil Filters provide a filtering efficiency of 98.7 percent at 20 microns.

AMSOIL DOMINATOR SYNTHETIC RACING GREASE
GRGCR-EA $14.85
   
AMSOIL DOMINATOR® Synthetic Racing Grease is engineered to protect high-performance bearings and chassis components in racing applications operated on snow, dirt, water or track. It provides superior protection for bearings operating under high-speed, high-heat and heavy-load conditions. NLGI #2 GC-LB

AMSOIL SYNTHETIC WATER RESISTANT GREASE
GWRCR-EA $9.50

AMSOIL Synthetic Water-Resistant Grease is an extreme-pressure grease formulated specially for wet-duty performance. Composed of premium-quality synthetic base oils and calcium-sulfonate complex thickeners, Water-Resistant Grease provides exceptional film strength, shear resistance, adhesion properties and mechanical stability. Its water-washout and sprayoff resistance are outstanding for applications frequently exposed to water.

AQUA SPORT 2 DEGREE PUMP WEDGE
YH-16003 $85.00
  
2° pump wedge for 2008-present Yamaha 1.8L Waverunner  watercraft. The pump wedge is CNC machined out of a single piece of 6061 Aluminum, finished in a black anodized coating that protects it from salt water and features a double-sided lip to retain silicone sealant and prevent cavitation. We extensively tested our pump wedge to ensure that there are no handling compromises. The pump wedge lifts the bow of your craft reducing drag and substantially improving top-speed.

AQUA SPORT ARP FLYWHEEL BOLT SET
YH-15003 $24.00
 
Custom set of ARP flywheel bolts. These bolts are forged and thread rolled after being heat-treated which provides up to 10-times longer fatigue strength. They are precision CNC-machined to exact specifications. Made from 8470 chrome moly steel, with 180,000 PSI tensile strength. Set includes 6 bolts and an instruction sheet. Fits all Yamaha 1.8L HO SHO SVHO personal watercraft.

AQUA SPORT ARP HEAD STUD KIT
YH-15001 $186.00
 
Custom set of ARP head studs. Part #: YH-15001. These studs are forged and thread rolled after being heat-treated which provides up to 10-times longer fatigue strength. They are precision CNC-machined to exact specifications. Made from 8470 chrome moly steel, with 200,000 PSI tensile strength. Set includes 10 studs, 10 12-point nuts, 10 parallel ground washers, and instruction sheet. Fits all Yamaha 1.8L Waverunner watercraft. Studs used to bolt down the cylinder head to the engine block.

AQUA SPORT BILLET MANUAL TIMING CHAIN TENSIONER
YH-10027 $100.00
  
Performance billet T6-6061 aluminum construction, anodized black finish, manual timing chain tensioner. Direct replacement for the factory automatic timing chain tensioner. Unlike the automatic factory timing chain guide, a manual timing chain tensioner will not loose it's setting and will keep the timing chain adjusted at all times. Comes with an o-ring to provide seal, no need for a gasket.

AQUA SPORT DUAL VALVE SPRING / TITANIUM RETAINER / SPRING LOCATOR KIT
YH-KIT1 $599.95
  
Our valve springs are made with premium super clean Chrome Silicon Vanadium Steel alloy for higher performance and durability at high rpm's and better memory. The valves are computer designed to ensure that wire stress levels do not overpass the limits of stress defined in the diagrams of fatigue for long durability under extreme conditions. Computer software also allows us to make sure that the harmonics are well under control limits.

Our spring locators are manufactured from hardened 4140 steel alloy that not only protects the cylinder head casting and shim, but also precisely locates and holds the valve spring in place.   These locators feature a CNC machined inside diameter which perfectly locates on the valve guide outside diameter with tighter tolerances than any competitor's locators. 

Our titanium retainers are made from Ti 17 or Ti 64 for the manufacturing of our retainers for excellent strength and wear resistance at 40% less weight than steel retainers. Our materials are tested and certified for chemical purity, uniform grain microstructure, and superior mechanical properties and sonically tested to be imperfection free. Precision CNC Machined.


AQUA SPORT EXHAUST VALVE SET
YH-10008 $347.00
 
Set of exhaust valves for Yamaha FZR Waverunner, eight 29mm valves are included. They are made from a one piece, forged Inconel alloy, fully CNC machined, and have a hard chrome treatment as well as hard tips. These exhaust valves for Yamaha are excellent for those looking to rebuild the cylinder head, or replacing bent valves, and wanting a high-power performance engine. Inconel is an alloy that cope well with very high temperatures, such as the temperatures exhaust valve are subjected to and attain, especially since, unlike intake valves, there is no fuel that goes through them that would be able to cool them down.

AQUA SPORT INTAKE MANIFOLD THERMAL INSULATOR GASKET
YH-12001 $48.00
  
Yamaha 1.8L Waverunner watercraft thermal insulating intake manifold gasket. Precision cut and designed to replace the listed oem gaskets. Gaskets helps to reduce heat transfer between the cylinder head and the manifold to decrease intake air temperature, and increase horsepower. Hotter air is less dense and thus has less oxygen per given volume, so less oxygen is available for combustion robbing you of power.

AQUA SPORT INTAKE MESH DELETE RING
YH-16002 $35.00 ( 2017 GP1800 )
 
Billet aluminum construction, CNC machined, anodized red finish. Replaces the mesh in the intake assembly to improve air flow and increase horsepower. Instructions included.

   
AQUA SPORT OXYGEN SENSOR MOUNT KIT
YH-16005 $120.00

The kit contains a mount anodized in black (to avoid things like corrosion, and other damages), 5 bolts, 1 allen key, and gasket.

  • Replacement to OEM plug
  • Easy to install
  • Made in USA

AQUASPORT THROTTLE BODY GASKET
YH-12009-K $5.95
 
Klingersil gasket material.

AQUA SPORT SINGLE VALVE SPRING / TITANIUM RETAINER / SPRING LOCATOR KIT
YH-KIT3 $540.00
 
Our valve springs are made with premium super clean Chrome Silicon Vanadium Steel alloy for higher performance and durability at high rpm's and better memory. The valves are computer designed to ensure that wire stress levels do not overpass the limits of stress defined in the diagrams of fatigue for long durability under extreme conditions. Computer software also allows us to make sure that the harmonics are well under control limits.

Our spring locators are manufactured from hardened 4140 steel alloy that not only protects the cylinder head casting and shim, but also precisely locates and holds the valve spring in place.   These locators feature a CNC machined inside diameter which perfectly locates on the valve guide outside diameter with tighter tolerances than any competitor's locators. 

Our titanium retainers are made from Ti 17 or Ti 64 for the manufacturing of our retainers for excellent strength and wear resistance at 40% less weight than steel retainers. Our materials are tested and certified for chemical purity, uniform grain microstructure, and superior mechanical properties and sonically tested to be imperfection free. Precision CNC Machined.


AQUA SPORT THROTTLE BODY MOUNT
YH-16001 $85.00
  
Billet throttle body mount for Yamaha 1.8L Waverunner. Billet aluminum construction, CNC machined, and anodized red. Includes stainless steel bolts and washers, as well as an Allen key to tighten the mount to the intake manifold and the throttle body to the mount. Much stronger than the plastic OEM one. Replaces OEM part # 6S5-14360-00-00. Made in the United States.

AQUA SPORT TITANIUM RETAINER SET
YH-10005 $313.00
  
Intended for OEM factory springs. Retainers are manufactured with high quality military cetified Titanium alloy and precision CNC machined for a tight fit that will ensure a long durability. Set includes: 16 Titanium Retainers We use both Ti 17 & Ti 64 for the manufacturing of our retainers for excellent strength and wear resistance at 40% less weight than steel retainers. Our materials are tested and certified for chemical purity, uniform grain microstructure, and superior mechanical properties and sonically tested to be imperfection free.

AQUA SPORT VALVE SPRING LOCATORS SET
YH-10002 $106.00
  
These premium quality valve spring locators are manufactured from hardened 4140 steel alloy that not only protects the cylinder head casting and shim, but also precisely locates and holds the valve spring in place. These locators feature a CNC machined inside diameter which perfectly locates on the valve guide outside diameter with tighter tolerances than any competitor's locators. Don't compromise high quality for a low price. Features: Protects the spring pocket/shim while properly locating & holding the valve springs in place This I.D. locator is engineered with the locating shoulder on the inside diameter Designed to handle the extreme spring pressures and high RPM in racing engines Heat treated for long life expectancy. 

ATLANTIS FLUSH KIT
A8582B $19.95

ATLANTIS PRO FLOATING WRIST LANYARD
A8130 $24.95 Black

BEL-RAY MARINE EXTREME PRESSURE WATERPROOF GREASE
99710-CG $10.95 14oz Cartridge
  
A heavy duty, premium grease fortified with Extreme Pressure additives. The addition of aluminum complex thickeners allows it to be virtually waterproof and ideal for items subject to direct contact with water. Unaffected by either salt or fresh water, it provides unsurpassed rust and corrosion protection on any treated surface exposed to harsh marine environments.

BELRAY OIL FILTER
SV57808 $8.95
 
Replaces:
Yamaha 69J-13440-00-00
Yamaha 69J-13440-01-00
Yamaha 69J-13440-03-00

BLOWSION VACATE VALVE
06-01-071 $31.95
  
A simple installation drain valve alternative for the OEM drain plug. Machined from 6061 aluminum and anodized for corrosion protection, the Vacate Valve operates using the forward motion of the watercraft and gravity to allow ingested water to simply vacate the hull in one direction only. Direct threaded replacement for the flimsy OEM plastic drain plugs, the Vacate valve also simplifies interior flushing of the engine compartment.

BOATLIFE MARINE SILICONE RUBBER
1140 $9.99 Tube Clear
1141 $9.99 Tube White
1142 $9.99 Tube Black
1150 $19.29 Cartridge Clear
1151 $19.29 Cartridge White
1152 $19.29 Cartridge Black
  
100% marine high quality silicone sealant. For use above or below the waterline. Will not shrink, crack, or dry out. Superior flexibility and adhesion to fiberglass, plastic, metal, and wood. Retains flexibility and tensile strength even after years of exposure.
Excellent for sealing transom and pump sections when installing impeller.

CALIBER TRAILER BUNK SLIDES
23010 $34.95 Black
23011 $34.95 White
23013 $34.95 Yellow

Makes launching your boat or watercraft easy, slides effortlessly off bunks and into the water.
  • The new unique profile provides extra cushioning between the boat and trailer bunks.
  • Washout channels flush sand and debris off of the slides and away from the hull.
  • Safer unloading and loading because of reduced friction and stress by 400% on the trailer cranking mechanisms, ropes and hull bow hooks.
  • Allows you to unload and load your boat or watercraft in shallower water.
  • Fast and simple installation.
  • Made from a low-friction composite which is impervious to sun, weather and salt water.

CALIBER TRAILER BUNK WRAP
23050-BK $49.95
 
16' roll covers up to two 2 x 4 x 8' bunks
Replace your old ripped carpeted bunks with a smooth permanent solution.
  • Less strain on arms, ropes, pulleys, and bow eyes
  • End Caps and All Stainless hardware included
  • Bunk Wrap mounts directly over bare wood

CANDOO GPS SPEEDOMETER MODULE
9510 $149.00

CORROSION TECHNOLOGIES CORROSION X
90101 $11.09 6oz
90102 $20.89 16oz
  
CorrosionX is the most advanced and effective corrosion prevention compound, lubricant and penetrant in the world! Although it may look like a typical oil-based anti corrosion spray, CorrosionX utilizes a revolutionary technology called Polar Bonding that does far more than merely slow down the corrosion process like those so-called 'corrosion inhibitors'. Corrosion-X actually kills existing rust and corrosion (keeping it from spreading) and provides long-term protection against rust and corrosion on any metal surface.

CRC 6-56 MULTI PURPOSE LUBRICANT
06007 $8.99
 11oz. Aerosol

06008 $49.99 Gallon

A versatile petroleum based compound that forms a clear, thin film that lubricates and protects against wear & corrosion. Multi-purpose product lubricates, protects, & displaces moisture all in one.

CRC SALT TERMINATOR
SX32M $29.99
32 Oz. with Mixer 
SX32 $17.99  32 Oz.
SX128 $39.99 1 Gal.

Cleans & protects anything exposed to salt  (saltwater, salt air, road salt ). Dissolves salt & leaves a protective coating to inhibit corrosion. Essential as a motor flush for marine engines in both saltwater and freshwater environments.

DEANS TEAM SPEED LIMIT CONTROL ECU REFLASH
DT-SLC-GP1800 $160.00
 
Send in your ECU for a Reflash to remove the factory speed limit control and gain 3-4 mph with no additional upgrades.
  • Easily increase top speed
  • Allows even more speed gains with other aftermarket upgrades
  • All dash functions remain intact 

 
 
DSS YAMAHA DRIVESHAFT HOLDER
TOOL53 $32.95
 
Required tool when removing impeller from driveshaft.

ENGINE TECH 17LB SUPERCHARGER WHEEL
ET-SVHO-17 $579.00

ENGINE TECH 19LB SUPERCHARGER WHEEL
ET-SVHO-19 $699.00

ENGINE TECH 23LB SUPERCHARGER WHEEL
ET-SVHO-23 $800.00

FIZZLE Y1000 INTERCOOLER KIT
FF-YM-IC-0018 $999.95
  • Includes authentic TiAL or HKS (your choice) blow off valve
  • Gain 2-3+ MPH top speed over OEM Yamaha SHO or SVHO intercooler
  • Gain 200-300+ peak RPMs, acceleration and throttle response
  • Kit Contents: The intercooler with blow-off valve flange, full piping kit, mounting bracket system, and cooling line fittings
  • Fits all supercharged Yamaha watercraft 2008-2017, including FZR, FZS, GP1800, FX SHO and SVHO models and supercharged Yamaha Jet Boats

   
   
   
   
HIFLOFILTRO OIL FILTER
HF740
 $8.95


HOTCAMS VALVE SHIM KIT
HCSHIM02 $89.95
  
9.48mm Complete shim kit 1.20-3.50mm in .05mm increments with 3 shims in each size

HT MOTO OIL EXTRACTOR
OIL01 $65.00

Make changing the oil on your 4 stroke jetboat clean and hastle free. Holds up to 6 liters (1.5 gal) in this sturdy portable container. Pump included.

HT MOTO OIL EXTRACTOR
OIL03 $130.00

Ideal for bigger jobs and shops, this larger capacity oil/fluid extractor makes changing the oil on your 4 stroke PWC, boat, snowmobile, ATV, lawn mower, etc. clean and hastle free. Holds up to 15 liters (3.92 gal) in this sturdy portable container with built in pump.

ISLAND RACING
BILGE PUMP KIT GP1800
IR-BPK-GP1800 $139.95

ISLAND RACING
ENGINE BREATHER KIT
IR-EBK-SVHO-B $24.95 Blue
IR-EBK-SVHO-R $24.95 Red
IR-EBK-SVHO-W $24.95 White

ISLAND RACING
ECONOMY BRACKET KIT GP1800 INTAKE GRATE REAR
IR-ECOBK-GP1800-IGR $74.95
IR-ECOBK-GP1800-IGR-BO $33.95 ( Bracket & Hardware only )
 
A MUST for ALL aftermarket intake grates on the GP1800

The ISLAND RACING ECONOMY INTAKE GRATE BRACKET KIT utilizes larger OEM style brackets Our kit eliminates the factory brackets which are prone to pulling through the hull on the GP1800 causing major hull damage and possible personal injury. Marine grade Stainless Steel hardware included. Available as a complete kit or bracket only.

ISLAND RACING
FUEL INJECTOR KIT 100LB 1000CC
IR-FIK-YAM-1000 $425.00
 
100% BRAND NEW GENUINE
Tested back to back with the EXTREMELY overpriced kits currently on the market. These are the same high quality injectors used on all our builds.

ISLAND RACING
HEAVY DUTY BRACKET KIT GP1800 INTAKE GRATE FRONT
IR-HDBK-GP1800-IGF $49.95

Our HEAVY DUTY INTAKE GRATE BRACKET KIT kit is designed to replace the weak factory cast front intake grate bracket with a heavy duty billet aluminum bracket. Marine grade stainless steel hardware included.

ISLAND RACING
HEAVY DUTY BRACKET KIT GP1800 INTAKE GRATE REAR
IR-HDBK-GP1800-IGR $99.95
IR-HDBK-GP1800-IGR-BO $64.95 ( Brackets & Hardware Only )
 
A MUST for ALL aftermarket intake grates on the GP1800

The ISLAND RACING HEAVY DUTY INTAKE GRATE BRACKETS are constructed from billet aluminum bar and are the finest brackets available on the market. The raw and textured finish provides outstanding sealant adhesion properties. Raw because unlike some other kits on the market, the sealant sticks to the bracket and not some coating applied to the bracket. Textured because it provides additional adhesion. Our kit eliminates the factory brackets which are prone to pulling through the hull on the GP1800 causing major hull damage and possible personal injury. Marine grade Stainless Steel hardware included. Additional top locking nuts and washers provided but not required for install. 

ISLAND RACING
INTERCOOLER COOLING & FLUSH KIT
IR-ICFK-SVHO-R $159.95

ISLAND RACING
INTERMEDIATE HOUSING ASSEMBLY
IR-IHA-406 $239.95

There are many low cost ( and low quality ) intermediate housing assemblies on the market. We have yet to see one that is assembled correctly or use anything other than an inferior quality bearing.

We utilize some of the aftermarket components to keep costs down but includes the OEM Yamaha bearing to insure both reliability and durability. Each housing is assembled individually and correctly to insure a quality part.

ISLAND RACING
MARINE LIQUID PUMP GREASE
IR-MLPG $14.95
 6oz


We are often asked what is the BEST grease to use in jet pumps. The answer is our MARINE LIQUID PUMP GREASE. Our grease is composed of MARINE lubricants and is blended specifically for use in jet pumps. Regular grease is too thick and once "flung" off the bearings will lead to failure in short time. Our Marine Liquid Pump Gease will flow to the bearings offering unequaled PERFORMANCE and PROTECTION. Recommended for jet pumps in ALL watercraft from stock to fully modified.

ISLAND RACING
PRO IMPELLER

Solas YV-CD-13/18 Based:
YV-CD-13/16-IRPRO $389.95
YV-CD-13/17-IRPRO $389.95
YV-CD-13/18-IRPRO $389.95
YV-CD-13/19-IRPRO $389.95
YV-CD-14/17-IRPRO $389.95
YV-CD-14/18-IRPRO $389.95
YV-CD-14/19-IRPRO $389.95

Solas YV-CD-13/20 Based:
YV-CD-13/18-IRPRO $389.95
YV-CD-13/19-IRPRO $389.95
YV-CD-13/20-IRPRO $389.95
YV-CD-13/21-IRPRO $389.95
YV-CD-14/19-IRPRO $389.95
YV-CD-14/20-IRPRO $389.95
YV-CD-14/21-IRPRO $389.95

ISLAND RACING
QUICK CONNECT FLUSH KIT
IR-QCFK-SE-B $54.95
( Blue )
IR-QCFK-SE-R $54.95 ( Red )

Replace your leaking, worn out OEM flush assemblies or just upgrade to our HIGH QUALITY, user friendly Quick Connect Flush Kit. Just a simple push and the couplers snap together forming a solid LEAKPROOF connection.
Excellent for adding a second flush assembly for intercoller flushing.

ISLAND RACING
QUICK CONNECT FLUSH KIT - BLACK EDITION
IR-QCFK-SE-B-BE $62.95
 ( Blue )
IR-QCFK-SE-R-BE $62.95 ( Red )

Replace your leaking, worn out OEM flush assemblies or just upgrade to our HIGH QUALITY, user friendly Quick Connect Flush Kit. Just a simple push and the couplers snap together forming a solid LEAKPROOF connection.
Excellent for adding a second flush assembly for intercoller flushing.

ISLAND RACING
SPARK PLUG INDEX WASHER KIT
IR-SPIWK-14 $29.95

Our SPARK PLUG INDEX WASHER KIT allows you to “index” or align the direction of the electrode for more efficient combustion, HIGHER HORSEPOWER, and HIGHER PEAK RPM. Washers are made from 100% Stainless Steel and will not corrode in marine environments. Washers are reuseable.

ISLAND RACING
T-BOLT HOSE CLAMP KIT - RIVA FREE FLOW EXHAUST
IR-TBCK-RY16060 $29.95

ISLAND RACING
T-BOLT HOSE CLAMP KIT -  RIVA REAR EXHAUST
IR-TBCK-RY15061 $39.95

 
 
ISLAND RACING
T-BOLT HOSE CLAMP KIT - WATERBOX
IR-TBCK-Y-SHO-WB $19.95

Exhaust leaks rob performance, lose races, and possibly flood your engine. Replace the weak OEM clamps with "Marine Exhaust Standard" 100% Stainless Steel T-Bolt Clamps.

ISLAND RACING
TOW VALVE KIT
IR-TVK-58 $24.95

Our Tow Valves bodies are 450PSI plated brass construction. Full flow inner diameter doesnt restrict cooling water. During towing situations, it's mandatory to shut off the inlet water hose to prevent engine damage.

ISLAND RACING
WATER STRAINER KIT
IR-WSK-12 $49.95 For 1/2" Hose
IR-WSK-58 $49.95 For 5/8" Hose

Our WATER STRAINER KITS are the finest kits available on the market.  Keep unwanted debris out of your engine and cooling system. Mounts in any position. Straight and 90 degree fittings allow for unlimited hose routing.  Marine grade mounting and hose clamps included. 

PURE ESTORLIN® MARINE 4-STROKE PERFORMANCE 10W/40
KE-334 $12.99
Quart
KE-335 $47.99 Gallon
  
Designed for all outboard, inboard, I/O and PWC four stroke engines
Certified warranty compliant
Provides performance advantages for leading outboard, inboard, I/O and PWC engines

KLOTZ JET PUMP LUBRICANT
KL-511 $6.95 4oz
  
TechniPlate Synthetic Lubricity System protects against expensive jet pump failures
Designed specifically for all machine jet pump drives
Anti-foam additives maintain lubrication efficiency
Preserves seals for reduced maintenance and down time
Contains red leak indicator

MAXIMA PWC MARINE 4T
14901
$8.25 10w40 Liter

PWC Marine 4T is a superior product featuring advanced additive technology in the development of highly stable and long life multi-grade PWC specific oil. By using an exclusive blend of petroleum base stocks and advanced anti-wear, anti-shear additives, this product assures viscosity stability for 4-cycle engines. This formula also has extra anti-scuff additives to handle extreme loads and peak temperatures in high performance engines. Exceeds FC-W specifications and all known OEM requirements.

   
   
NGK SPARK PLUG 
LFR7A $7.95

   
OPPAMA ENGINE TACHOMETER
PET-2100DXR $299.95

PARTS UNLIMITED AGM MAINTENANCE FREE BATTERY
2113-0043 $96.95 ( Yuasa Equivalent YB16CL-B )

Parts Unlimited batteries are a high-quality, low-cost alternative to OEM battery replacement
Built to the same exacting specifications and quality-control standards as top brand-name Japanese batteries
Rugged and reliable starting power for your machine
All batteries are shipped dry
Acid pack included ( UPS Shippable ) 

   
PERMATEX ANTI-SEIZE LUBRICANT
81343 $4.95
1oz
  
Use of anti-seize is highly recommended for spark plug installation.



PERMATEX DIELECTRIC GREASE
22058 $13.95
  • Water-repellent grease works great for sealing electrical connections
  • Excellent lubricant for rubber, ceramic and plastic-with a high-temperature resistance
  • Stops corrosion on electrical connectors
  • Use for lubricating O-rings, gaskets and seals

PERMATEX MOTOSEAL GASKET MAKER
29132 $7.95

Excellent for sealing supercharger housing when installing aftermarket wheel. 

PERMATEX THE RIGHT STUFF GASKET MAKER
25229 $21.95

   
PROK AIR FILTER
006-590 $116.95
  • OEM stock replacement air filters
  • Washable and reusable to maximize performance and budget
  • Clean air filters increase airflow, meaning more power and greater performance

R&D INTAKE GRATE
112-18005 $349.95
  
( Pump seal kit not included ) 

R&D BILLET SUPERCHARGER SHAFT
612-25020 $369.95

R&D's High Performance Billet Supercharger Shaft eliminates the weak design features of the OEM supercharger shaft. When increasing performance (boost) it’s recommended to upgrade to the R&D Shaft to ensure you will not have shaft failure.

The R&D Shaft is precision CNC machined from one piece of high grade Super Steel Alloy, heat treated, and precision ground to spec. The Shaft and Gear are ONE PIECE, (not a pressed together assembly like stock) to guarantee that under ANY boost pressure the gear will not break off the shaft. The one piece design will also eliminate gear slippage under high boost loads and increased heat.

The R&D Shaft also features a larger upgraded and fortified thread diameter that will not fatigue or break under extreme conditions. The larger thread diameter will also allow wheel torque specs to be increased safely.

The Ultimate Shaft is also 17% lighter than all other shafts on the market. This reduced reciprocating will extend supercharger clutch life.

Used by Yamaha Factory Race Teams. Kit comes complete with Billet Shaft, new larger nut and installation instructions.

All in all, the new R&D Ultimate Billet Shaft is not just a replacement shaft, but a solution to end all supercharger shaft problems. The R&D shaft has proven over the years to be super strong and reliable in any condition. And it’s available for the best price too.

R&D also offers a bearing rebuild kit to replace worn supercharger bearings Pt. # 612-25025

• Superior billet material strength
• Precision heat treat and ground finish for reduced friction 
• Upgraded thread size 
• One piece gear/shaft design is much stronger than O.E.M. 
• 17% lighter weight 
• Increased supercharger and engine protection 
• Improved clutch life 


R&D LOW FRICTION DUAL WASHER IMPELLER SPACER KIT
132-81111 $54.95
  
The R&D “Dual Washer” Impeller Spacer Kit replaces the O.E.M. single seal washer with a specifically designed and machined kit that incorporates a second low friction slip washer to be used which allows impellers to be removed with 50 percent less torque during the impeller removal process! Tired of Impellers that are so galled up that impellors have to be machined or cut off? Tired of broken impeller tools and broken vises? Install the R&D low friction “Dual Washer” Kit and impeller removal will be super easy when making impeller changes. Many SVHO owners have had these issues and have had to cut up and throw away impellers and repair damaged threads. The R&D Kit puts to end all the expensive repairs and downtime with these issues. The R&D “Dual Washer” Kit fits all Yamaha models both supercharged and N.A. from 2008 and up.

R&D POWER PLENUM FLAME ARRESTOR
200-01800 $139.95
 
The R&D High Flow Filter design replaces the restrictive stock filter inside the OEM air box. This is the only performance filter that utilizes the water resistant OEM air box, allowing improved air flow. Why? Because replacing the OEM paper filter element with the R&D high flow filter allows more air flow which equals more power and improved performance. The washable and reusable design means this will be the last filter you will ever have to buy.

R&D PUMP SEAL KIT
162-00022 $79.95 For Stock Scoop Grate
162-00023 $79.95 For R&D Aquavein Scoop Grate
  
R&D's GP1800 pump seal kit stuffs up all the unwanted cavities in the pump shoe that aid in producing cavitation. This kit offers a great way to seal the pump shoe to reduce cavitation and increase pump efficiency and performance.

RHAAS URETHANE MOTOR MOUNT
YAM4STRMOUNT $50.00
  
These mounts are made from 6061 aluminum and anidozed for corrosion protection and a long life. The urethane is locked into the base and the threaded insert to provide a one piece, mechanical lock on all components. These mounts do not rely on glue to hold things together, the mount is molded at one time with the billet threaded insert and the billet aluminum base. These are made to the highest standards in our own manufacturing facility right here in the USA. There is 4 years of R&D that went into making these mounts the best you can buy for your Yamaha.
Motor mounts sold individually.

RIVA BILLET DRIVESHAFT SLEEVE KIT
RY30060-DSS $54.95
 
  • Direct heavy-duty replacement for original thin rubber hose.
  • Anodized to prevent corrosion.
  • High quality AH&E silicone couplers.
  • Overlapping clamp design features smooth inner surface to prevent coupler damage.
  • Recommended for all performance applications.

RIVA BILLET PUMP STRAINER
RY1013-WS-80 $89.95
 
Billet pump strainer allows installation of a second cooling line for the SVHO engine. Larger openings increase water pressure for more cooling to engine. Replaces restrictive OEM pump strainer on SVHO model.

RIVA FREE FLOW EXHAUST KIT
RY16060 $199.95
 
Replaces the restrictive sound suppression system located between the water box and hull exit on your watercraft improving engine performance by reducing back pressure and harmful detonation. Made from mandrel bent aluminum tubing, bead rolled on the ends to secure couplers, and powder coated to prevent corrosion. Includes high temp silicone replacement coupler and installation instructions.

ISLAND RACING
T-BOLT HOSE CLAMP KIT -  RIVA FREE FLOW EXHAUST
IR-TBCK-RY16060 $29.95

RIVA FUEL PRESSURE REGULATOR KIT GP1800
RY12070-RRFPR-6S5 $474.95

Riva's Fuel Pressure Regulator Kit provides the precision pressure control necessary to compliment aftermarket ECU applications on the SVHO engine. Kit is fully assembled & mounts securely on top of fuel tank via sturdy aluminum bracket. High quality billet pressure regulator can adjust base pressure from 25 to 80 PSI. Unit can also be set up as rising rate fuel pressure regulator at a 1 to 1 ratio providing one additional pound of fuel pressure for every pound of boost gain. Plugs directly into original fuel system with OEM connectors and features a large 3/8" fuel return line that is routed through supplied rubber fuel tank cap. Includes integrated liquid-filled pressure gauge and billet Fuel Pressure Regulator Block-Off necessary for removal of stock fuel pressure regulator in fuel tank.

Key Features Include:
Precision fuel pressure control with optional rising rate function.
High quality stainless steel liquid-filled pressure gage.
Large 3/8 fuel return line.
Includes billet Fuel Pressure Regulator Block-Off.
Easy bolt-on installation with OEM fuel connectors.
Includes complete installation instructions & tuning guide.

RIVA HANDLEBAR EXTENSION SET
RY24061-BES $59.95

The RIVA Yamaha RiDE Grip Installation Kit allow easy installation of aftermarket grips to replace the original oversized grips. Billet fitting mounts securely to ends of original handlebars via machined locking feature. Includes special locking clamps to secure 130mm ODI grips.
  • Allows installation of popular ODI 130mm grips on Yamaha RiDE models.
  • Precision-machined from 6063 billet aluminum.
  • Anodized to prevent corrosion.
  • Sold as a pair (grips sold separately).

RIVA HIGH FLOW BILLET FUEL RAIL
RY12040-BFR $259.95
 
Our High Flow Fuel Rail is an essential upgrade to your fuel system to support increased horsepower from supercharger or turbo modifications. Directly replaces restrictive factory fuel rail for improved fuel delivery and enhances the appearance of your engine bay. Precision machined billet aluminum rail features a unique bracket system that adapts to a variety of injector sizes & lengths. Large body design provides increased flow capabilities to support 500+ horsepower applications. Inlet fitting accepts OEM Yamaha fuel connector for easy plug-in installation. Includes fittings for flow-through fuel routing to eliminate injector supply fluctuation and keep fuel cooler. Can also be set up with OEM dead head routing via supplied fuel pressure gauge or plug. Constructed of 6061 billet aluminum and anodized to prevent corrosion. Includes all necessary mounting hardware and complete installation instructions.

Key Features:

  • High flow fuel delivery supports more power.
  • Fits all Yamaha OEM injectors along with RIVA 100lb Pro-Series Fuel Injectors (part# RY12040-I-KIT-100).
  • Accepts OEM Yamaha fuel connector fitting for easy installation.
  • Delivers equal fuel supply to injectors with flow-through fuel routing.
  • Billet aluminum construction and anodized to prevent corrosion.
  • Can also be used on stock engine with stock injectors for cosmetic upgrade.

RIVA HIGH PERFORMANCE VALVE SET
RY19040-HPV-0 $649.95
 
RIVA High Performance Valves are engineered to improve reliability and performance in high-boost supercharged & turbocharged engines. Intake valves are built from high grade EV-8 (24-4N) stainless that is extremely resistant to corrosion. Exhaust valves are built from inconel alloy (IN-751) that is highly resistant to heat damage. Valve heads have been redesigned for increased air flow and durability. Valve stems feature hard-chrome plating for superior wear & lubricity. Kits include high strength valve locks, precision machined from 4130 chromoly.

Drop-In Valve Kits: Direct drop-in replacement valves require no machining of cylinder head.
Oversized Valve Kits: +1mm Intake & +1mm Exhaust valves deliver more air flow (requires machining of cylinder head).

  • Stronger & lighter than stock valves.
  • Redesigned valve heads for improved air flow & strength.
  • High grade stainless intake valves resist corrosion.
  • Inconel exhaust valves resist heat from high boost applications.
  • Valve stems are hard-chrome plated for improved wear.
  • Includes high strength valve locks.
  • Sold in sets of 16 (8 Intake/8 Exhaust).

RIVA HIGH VOLUME FUEL PUMP KIT
RY12040-340FP-6S5 $199.95
 
This High Volume Fuel Pump Kit delivers 340LPH to support modified supercharged & turbocharged engine packages. RIVA pumps utilize a turbine pumping mechanism that increases durability and fuel delivery. Detailed installation instructions supplied with each kit.

RIVA INTAKE GRATE
RY22110 $299.95
 
Our revolutionary new intake grate for GP1800, VXR and VXS delivers the ultimate in speed, hook up & strength. All new design features oversized top loader wing and optimized inlet ramp for closed course and offshore racing. Bulletproof stainless steel construction makes this grate virtually indestructible and eliminates the need for additional restrictive support bars. Race bred design significantly reduces cavitation and provides superior handling along with unmatched durability in extreme conditions.
Key Features:
  • Dramatic increase in hook up due to new top-loader wing design & inlet ramp
  • Improved top speed in rough water conditions
  • No top speed loss on smooth water
  • Race bred design provides excellent handling
  • Significantly reduces cavitation
  • Bulletproof stainless steel construction tested at 90mph

RIVA INTAKE MANIFOLD UPGRADE KIT
RY12040-IMUK $39.95 ( 2017 GP1800 )
  
Riva's Intake Manifold Upgrade Kit enables your SVHO engine to produce more horsepower by delivering increased air flow and boost pressure (+1lb). Precision tapered billet sleeve directly replaces restrictive mesh element in intake manifold. Provides improved low end punch and mid range pull through quick & easy installation. Includes detailed installation instructions.

RIVA MAPTUNERX  YAMAHA 1.8L BUNDLE
RY110SC-B $997.35
The MaptunerX Bundle delivers instant plug-in horsepower!

Quickly and easily load performance tunes into your Yamaha PWC eliminating the need to ship out your ECU for programming. Features a slick, full color, touch screen display. There is no limit to the number of vehicles or tunes you can reflash with the MaptunerX. Simply purchase one additional tuning license for each vehicle that you would like to program. Includes full access to RIVA's world famous tuning library along with unmatched technical support. Easily switch between performance tunes and then back to stock settings if you wish.

RIVA PERFORMANCE BLOW-OFF VALVE KIT
RY17040-BV $379.95
  
Riva's Performance Blow-off Valve Kit improves supercharger reliability and performance by relieving unwanted pressure during off-throttle operation. Reduces supercharger clutch & gear wear and eliminates heat soak in discharge tube. High-strength silicone hose with integrated HKS valve installs easily in place of OEM elbow joint. Includes high quality HKS Super SQV (Super Sequential Blow-off Valve) that features unique sequential valve structure and a differential pressure control system, allowing for a broad operation boost range. Also includes vacuum line and fittings necessary for installation on SVHO & SHO engines. A simple and cost effective upgrade for both stock and modified engines.

RIVA POWER FILTER KIT
RY13110 $299.95
 
Our Power Filter feeds your supercharged engine a steady diet of cool air delivering greatly improved acceleration and rpm. Replaces restrictive stock air box with a high-volume, precision-formed intake duct that attaches to the supercharger via a large 4” adapter. Cool air enters the system via an oversized K&N filter element. Includes detailed installation instructions.

RIVA PRO SERIES SPONSONS
RY26110 $499.95
 
Our race proven Pro-Series Sponsons deliver dramatically improved handling & straight line stability with superior fin & backing plate design. Features a cutting edge stepped surface for unmatched control. Bulletproof mounting system utilizes aluminum inserts for maximum strength. Fully adjustable three position fin to control the amount of influence they have on the craft. Easy bolt-on installation uses original mounting points. Includes all necessary hardware and installation instructions.
  • Improved handling and straight line stability
  • Fully adjustable three position fin
  • Easy bolt-on installation
  • Race proven design

RIVA REAR EXHAUST KIT
RY15061 $369.95
 
Our rear exhaust kit for 2015+ Yamaha VXR/VXS delivers performance and cutting-edge style. Allows for removal of restrictive sound suppression system located between water box and hull exit. Improves engine performance by reducing back pressure and restriction. Includes mandrel bent aluminum exhaust tube that is powder coated to prevent corrosion, large billet through-hull exhaust outlet, billet OEM exhaust outlet block-off and high-temp silicone couplers along with all necessary mounting hardware & installation instructions.

ISLAND RACING
T-BOLT HOSE CLAMP KIT -  RIVA REAR EXHAUST
IR-TBCK-RY15061 $39.95

 
 
RIVA RIDEPLATE
RY21110 $249.95
  
Riva's new GP1800 Ride Plate delivers the perfect balance of increased top speed and improved handling in a variety of water conditions. Its race bred design features deep channels for improved acceleration and traction in turns. Provides excellent straightline stability at high speed with reduced porposing. Easy bolt-on installation accepts OEM speedo sensor.
  • Superior handling performance
  • 2 MPH Top Speed Increase!
  • Improved acceleration
  • Reduced porposing
  • Improved straight line tracking at high speed
  • Powder coated to prevent corrosion
  • IJSBA Race Legal

RIVA STAINLESS STEEL WEAR RING
RY33-160-YV $499.95

Our heavy-duty, 100% stainless steel wear rings/impeller liners are the perfect replacement for your damaged original unit. Durable solid stainless steel construction resists debris damage and saltwater corrosion. Original Yamaha wear ring is constructed of cast aluminum with a thin stainless steel liner that is pressed into place. Corrosion quickly develops between the dissimilar metals swelling the thin liner until it closes down and jams against your impeller. When well cared for, our stainless steel wear rings will provide years of trouble free use. Directly replaces OEM part# 6ET-51312-00-00

RIVA SUPERCHARGER IMPELLER F1 17 PSI
RY17080-SCI-F1 $579.95
 
Presenting the ultimate (drop-in) supercharger impeller for the Yamaha SVHO Engine! Designed to deliver more horsepower and torque throughout the RPM range resulting in excellent acceleration and top speed. Precision machined from billet aluminum to ensure exact tolerances and anodized to prevent corrosion. All new blade design is optimized aerodynamically and high speed balanced for smooth operation. Installs easily into stock supercharger housing with no modifications required. Includes detailed installation instructions. Produces 17psi @ 8,500rpm.

RIVA SUPERCHARGER IMPELLER F2 19 PSI
RY17080-SCI-F2 $699.95
 
Presenting the ultimate (drop-in) supercharger impeller for the Yamaha SVHO Engine! Designed to deliver more horsepower and torque throughout the RPM range resulting in excellent acceleration and top speed. Precision machined from billet aluminum to ensure exact tolerances and anodized to prevent corrosion. All new blade design is optimized aerodynamically and high speed balanced for smooth operation. Installs easily into stock supercharger housing with no modifications required. Includes detailed installation instructions. Produces 19psi @ 8,500rpm.

RIVA SUPERCHARGER IMPELLER F3 23 PSI
RY17080-SCI-F3 $799.95
 
Presenting the ultimate (drop-in) supercharger impeller for the Yamaha SVHO Engine! Designed to deliver more horsepower and torque throughout the RPM range resulting in excellent acceleration and top speed. Precision machined from billet aluminum to ensure exact tolerances and anodized to prevent corrosion. All new blade design is optimized aerodynamically and high speed balanced for smooth operation. Installs easily into stock supercharger housing with no modifications required. Includes detailed installation instructions. Produces 23psi @ 8,500rpm.

RIVA SUPERCHARGER SHAFT UPGRADE KIT
RY17040-UK-6S5-3 $499.95
 
Riva's Super-Duty ‘GEN-3’ Supercharger Shaft Kit provides the ultimate in reliability for high boost applications. Kit features a revolutionary hydraulic shaft stabilization bearing that limits shaft deflection and wear. Bearing stabilizes end of supercharger shaft via high pressure oil film dramatically increasing the stability of the system. Hydraulic end bearing and one-piece shaft bearing are fed by a through-shaft oiling system providing superior lubrication. Oil is delivered by braided stainless line and injected into a billet end cap that houses hydraulic bearing. Shaft is precision machined from a single piece of high-strength billet steel producing shaft, collar & gear as one piece. This eliminates the common failure point on stock shafts where OEM gear is pressed onto shaft. Shaft also features larger diameter threads & nut for added strength. Kit includes new one piece bearing with increased surface area providing improved torsional stability of shaft. Bearing features superior materials & finish treatment for reduced friction & abrasion resistance. This Shaft & Bearing Kit is a direct replacement for OEM parts and requires no additional modifications for use.

RIVA THERMOSTAT DELETE KIT
RY1013-40-TR $22.95
 
Allows Yamaha SVHO, SHO & HO engines to run cooler by replacing the thermostat with a specialized restrictor. Ideal for modified watercraft operating in high air & water temperatures. Designed to be used with RIVA Engine Cooling Upgrade Kits. Precision machined restrictor includes o-ring system for superior sealing in thermostat housing. Includes complete installation instructions.

RIVA VALVE RETAINER UPGRADE KIT
RY19040-SRU $349.95
 
Riva's Valve Retainer Upgrade Kit increases the reliability of your engine by reducing the possibility of valve float at high rpm. Includes 16 lightweight, precision-machined titanium valve retainers. A must for IJSBA & APBA Stock Class race craft.

RIVA WATERBOX
RY16041 $419.95
 
Developed on our Dyno and tested extensively on the water, this water box features radiused exhaust tubes and end caps for optimum exhaust flow. Unique exhaust baffle will increase the low-end power and mid-range pull of your Yamaha watercraft. Delivers up to 15hp on modified engines along with significant torque gains. High-strength aluminum construction will survive backfires and meltdowns. Powder coated to prevent corrosion. A must for modified motors.

SBT IMPELLER HOUSING
78-412-01 $262.85

SBT IMPELLER HOUSING INSERT
78-412-02 $41.85
 
Replacement insert for SBT Impeller Housing 78-412-01

SOLAS DRIVESHAFT HOLDER
WR014H $29.95

Required tool when removing impeller from driveshaft.

SOLAS CONCORD IMPELLER
YV-CD-13/18 $316.95
YV-CD-13/20 $316.95
YV-CD-14/21 $316.95

SOLAS IMPELLER HOUSING STAINLESS
YVS-HS-160 $429.95

SOLAS IMPELLER TOOL
WR014 $16.95

SOLAS IMPELLER TOOL
WR014A $16.95
  
For new YV & YS impellers requiring larger tool
Some hubs may be marked with an "A" in red

SOLAS STAINLESS STEEL 12 VANE PUMP STATOR
YVS-SV-160/74 $999.95 ( 160mm )

SLP FLOW-RITE INTAKE KITS
14-197 $24.95
 2"
14-258 $47.95 4"

Eliminate air intake restrictions by installing the Flow-Rite™ in the the intake tract for more air box feed or anywhere on the body where more air is required. The Flow-Rite™ is supplied with a pre-filter that repels water, yet passes air right through. A must for modified engines. Sold per each.

THREEBOND SILICONE LIQUID GASKET
TB1211 $23.95

TDR WATERBOX
02-0085 $295.00

TRAIL TECH TTO TACH-HOUR METER
742-A00 $44.95 Black
  
The surface mounted TTO Digital tach-hour meter allows you to easily monitor RPM and hours of use.

   
 
WET WOLF ADJUST-A-THRUST PUMP CONE
YAM5 $169.00
  
2014+ 160mm pump 4-bolt cone

   
WORX BILLET ENGINE COUPLER
WR04003 $382.00
  • Billet Drive coupler for Yamaha 1.8 Engine
  • Fits any 1.8 Yamaha Engine
  • Billet construction huge strength upgrade over stock cast unit
  • Utilises OEM rubber coupler
  • A must for any High Horsepower/ Race watercraft

WORX DROP IN STEERING STEM
WR06028 $599.00

WORX FREE FLOW EXHAUST
WR04028 $249.00
 
Allows removal of restrictive sound suppression baffles in Exhaust
Requires NO drilling of holes utilising OEM outlet in pump tunnel
No modification of OEM hoses needed so ski can be returned to stock
Billet anodised outlet fits directly into OEM location
A must for any modified craft

WORX HANDLEBAR EXTENSION
WR06032 $40.00

Billet anodized construction
Allows fitment of 130mm ODI lock grip
Easy install
Billet endcap design to prevent grip sliding off if lock clamp fails
Included hardware

WORX HI FLOW PUMP STRAINER SVHO
WR04046 $70.00
  
Larger openings for increased water flow into engine for lower engine temps.
Suits any late model 160mm jet unit.

WORX INTAKE GRATE
WR246 $245.00
 
The Yamaha GP1800 SVHO, 2015+ VXR is the ultimate fun machine and it is with great excitement Worx Racing Components bring to you their WR246 Intake Grate designed specifically for this new model. This intake grate is a must have for both recreational riders and racers wanting to get the very best from their new GP1800 or VXR.
Designed for the ultimate hook-up and handling, this intake grate combats cavitation in choppy to rough water conditions, maximises acceleration and even adds top end speed. Stability and cornering ability are also improved, this is a huge benefit when towing water skiers or other water toys. In testing, Worx owner Gary Watson discovered that this grate paired with Worx sponsons (WR552-I) completely transformed the all round handling of this boat.

   
WORX PUMP COOLING PLATE
WR04030 $44.00 ( Single )
WR04031 $48.00 ( Double )
  
The Worx pump cooling plate is a billet anodised plate that fits directly onto the OEM Yamaha Jet unit allowing an extra water fittings to be added to your watercraft's cooling system. A must for high horsepower applications.
BRASS FITTINGS NOT INCLUDED.

WORX PUMP SEAL KIT 2015+
WR07010 $98.00
 
Yamaha Pump Plug Kit WR07010, Improves pump intake dynamics by changing the shape and flow of the standard pump intake system.
This kit goes perfectly with the Worx Scoop Grate WR246 (also for the Yamaha GP1800/VXR,VXS 15+.)The Kit is easy to fit and provides immediate improvement on stock.

WORX REAR EXHAUST KIT
WR04045 $359.00
 
The Worx rear exhaust kit will eliminate any exhaust restriction, increase engine performance and give your Ski the “This means business look” with the Huge 3 inch Billet anodised outlet.Moulded Black silicone hose for easy install.
 
Billet anodised black 3 inch exhaust outlet
Billet anodised block off plate
Eliminates restrictive sound suppression baffles
Silicone hose reduces exhaust resonance and droning
A must for High horsepower/ Race craft

WORX RIBBON REMOVER 2017
WR04001 $38.00

WORX RIDEPLATE
WR317 $334.00
 
Worx have created a ride plate that is more predictable on turn in, letting you enter the turn with more speed. It sets the ski up, keeps the back of the ski locked into the turn. The back of ski does not slide and fall through tight slow speed turns. You are able to maintain throttle through the turn and it will let you have a full trim range of the ski, making the ski more stable and predictable at high speed.

WORX SPONSONS
WR522-I $370.00
  
Designed not just for cutting edge performance but killer style! Same best selling Worx Racing paddle now with billet insert for 4 point adjustment to personalise your watercraft to your own unique riding style!
Includes backing rails and all necessary hardware.
  
Product benefits include:
  • Greater stability
  • Improved cornering
  • Superior handling

WORX THROUGH HULL FITTING 1/2 INCH
WR06004 $27.00
 
Allows for easy installation of extra 1/2 inch cooling lines.

WORX TRIM EXTENSION
WR06021 $33.00
  
Increases trim range to bring the nose of your boat higher and increase speed!

   
   
   
   
YAMAHA IMPELLER HOUSING
6ET-51312-00-00 $327.41 

YAMAHA OIL FILTER
69J-13440-03-00 $24.00

YUASA BATTERY
YB16CL-B $79.95
  • Only Yuasa has Yumicron, the most powerful lead-acid battery of its size that appears as original equipment on more and more watercraft
  • All Yumicron batteries are shipped dry ( Acid not included )

YUASA BATTERY
YTX20HL-BS-PW $129.95
  • HIGH PERFORMANCE AGM MAINTENANCE-FREE
  • This new generation of maintenance-free batteries delivers higher cranking amps for vehicles that require extra starting power
  • Additional cranking amps make these one of the most powerful batteries on the market
  • Acid Pak included ( Continental USA Ground Shipping Only )

YUASA BATTERY
YTX20HL-PW $129.95
  • HIGH PERFORMANCE AGM MAINTENANCE-FREE
  • This new generation of maintenance-free batteries delivers higher cranking amps for vehicles that require extra starting power
  • Additional cranking amps make these one of the most powerful batteries on the market
  • Factory Activated ( Continental USA Ground Shipping Only )